Engine Performance Parts - 350Z

Engine Performance Parts - 350Z

*NEW PRODUCT* Kinetix SSV Intake Manifold for 2003-2006 Nissan 350Z / G35
Part # Kin SSV MANI
Newly released Velocity Intake Manifold features: Velocity plenum chamber design - Equal air flow between cylinders 12% more plenum chamber volume 10% short intake runners for more flow and higher HP potential Smoother A/F curve - less tuning required - more consistent power High RPM power !! 30.5hp gains at 6800 rpm Thicker gauge construction for higher boost - warranty up to 30psi The new Velocity Manifold is geared for higher flow and higher RPM power gains. This allows for even larger power gains in the many F/I vehicles out there. This manifold is constructed entirely of Stainless Steel, then polished out for an absolute beautiful finished product that looks as great as it performs. We chose stainless because of its great thermal properties, conducting 10X!! less heat than aluminum and eliminating much of the manifold's mass, which greatly helps with heat soak. Stainless is considerably more expensive than aluminum, but the finish shines brighter and longer. The overall manifold SAVES 10lbs of weight over stock! Precision TIG welding throughout, and a CNC cut 3/8" main flange. All mandrel bent runners and charge tube, this manifold rivals the quality of other intakes twice its price. We improved greatly upon the factory plenum designs. The factory lower plenum creates MANY dips and turns which do not promote good airflow and create turbulence inside your factory intake. We developed a straight shot design, eliminating the twists, turns, and obstructions. We then took each runner and also added velocity stack inlets to each individual runner for even better performance. This Manifold is a DIRECT replacement and will work with any aftermarket intake. It also allows you the ability to use the factory strut bar, or any aftermarket strut bar. We also have available an engine cover specifically designed for our manifold. Each manifold is supplied with all necessary hardware and instructions. There is an additional port supplied which can be used for boost gauges, etc.
MSRP $899.99
Your Price $729.99

NEW PRODUCT AEM Inline Water Injection Filter
Part # AEM 30-3003
The AEM Water/Methanol Injection Filter is an in-line filter that uses a micronic mesh screen to filter particulates as small as 40 microns. This allows a cleaner flow of water/methanol to be passed into the engine, not only protecting the internals of the engine itself, but also the working parts of the water/methanol pump, too. Run the AEM Water/Methanol Injection Filter in-line before the pump to protect both pump and engine. Simple to install, takes less than a minute. Fits virtually every Water/Methanol system on the market. Polypropylene housing - rugged material that is compatible with high concentrations of methanol. Completely Serviceable Assembly - can be disassembled, cleaned and reused for a long service life. Stainless Steel mesh strainer - AEMs custom mesh strainer filters down to 40 microns - MUCH smaller than similar filters. Large Filtering Area assure long service life and does not significantly reduce flow. Micronic Mesh Screen out-performs sintered filters in both filtering and serviceability.
MSRP $36.25
Your Price $26.10

NEW PRODUCT AEM Water/Methanol Flow Gauge 500cc or 1000cc
Part # AEM 30-5141/2 B/W
If you are using a Water/Methanol Injection System and want to know exactly how much fluid you are actually injecting into your engine, the AEM Water/Methanol Flow Gauge is a must. It replaces the "dummy light" with actual data displayed on a smooth moving needle-type gauge that allows you to accurately monitor the status of your injection system in real time. The gauge kit includes a precision flow sensor and fittings for use with 1/4" OD nylon tubing, so the AEM Water/Methanol Flow Gauge fits most Water/Methanol injection kits on the market today. For best results the 0-1000CC Flow Gauge should be used on Water/Methanol kits injecting up at least 500 cc/min and is ideal for those with the AEM Water/Methanol kit using the large sized nozzle (.630 jet size). If you are using the small or medium AEM nozzles, we suggest the 0-500CC Flow Gauge.
MSRP $276.25
Your Price $198.90

NEW PRODUCT Kinetix V+ Plenum for 2003-2006 Nissan 350Z / G35
Part # Kin V+ Plen
NEWLY RELEASED V+ intake plenum for the 350Z and G35 03-06 with new LOWER PRICE !! Improved in EVERY aspect over their previous intake plenum, including performance: * 270% stronger than previous plenum * Incredible heat resistance, improved 170%, now up to 500 degrees * Incredible heat resistance, improved 170%, now up to 500 degrees F * Lower operating temperatures - 50 degrees cooler than ANY aluminum plenum option * More volume! 20% more volume than factory and 12% more than our previous version * Completely smooth underside with NO flow restrictions * Can handle boosted cars, with lifetime warranty on cars up to 15 psi * Lifetime Warranty This new intake plenum replaces the upper half of your factory intake manifold. This plenum bolts directly up to your car with zero modifications, and also allows the use of the factory strut bar, and engine cover. This unit will fit the 350z, the G35, and the FX. * engine cover may not fit with the G35 or the FX35 This plenum increases the volume to the middle and more importantly the front cylinders. The factory plenum utilizes a very aggressive angle as it caps off the front cylinders. This new plenum equalizes the flow to all cylinders, while also increasing the total plenum volume. This plenum also uses a very versatile plastic to achieve a smooth interior for superior flow properties. The plastic also allows a lighter overall weight, by about 3 lbs. The overall temperatures of the plenum have also decreased by about 50 degrees Fahrenheit. This helps with heat soak problems and to help lower air intake temperatures.The plenum has shown a solid peak gain of 14 rwhp and a consistent gain throughout the RPM range. When matched up with high flow cats, they together have shown peak gains of 20 rwhp. The plenum still retains all factory mounting points and also includes all necessary new hardware. The plenum also includes a permanently adhered flange gasket that is to be used with the factory gasket as well as a new throttle body gasket.
MSRP $349.99
Your Price $249.99

**END OF YEAR SALE - AEM Water Injection Kit FREE SHIPPING**
Part # AEM 30-3000
The Water Injection Kit is an economical, complete install kit with no extra parts needed, user-friendly setup solution for reducing air inlet temps and increase charge density in boosted vehicles. Allows the user to safely run higher boost pressures and suppress detonation allowing the utilization of more timing and boost. Performance will no longer be compromised when running lower octane fuels. Features a high-pressure pump with progressive controls, a 1 gallon tank with integral fluid level sensor, interchangeable nozzles for easy flow adjustment and an integrated system status dash light with easily identifiable error codes including short circuits, battery voltage problems and low fluid warning. Key Features: Complete kit, everything is included Progressive controller driven 150 PSI pump 1 gallon tank with integral fluid level sensor Dash light for system status and low fluid warning Alcohol Compatible (up to 50% in solution with water) Progressive controller, provides boost dependent variable flow Provides output to either decrease timing or boost if the system runs out of fluid or detects an error Kit includes three jets to match your power requirements
MSRP $548.50
Your Price $395.10

New Product - Powerhouse Racing Vacuum Distribution Plenum
Part # PHR VacDisPlen
Anyone that has ever tried to connect a boost gauge, electronic boost controller, fuel controller, fuel pressure regulator, blow off valve, and TPS sensor to the intake plenum knows all to well the mess of hoses and T's and connections going everywhere from a single source. PHR has designed the VDP (Vacuum Distribution Plenum) to solve this issue and simplify all the hose routing. Now, a single 6mm hose connection to the intake plenum gives you 6 hose connections, enough to run any combination of sensors, gauges, and components. What's more, the hose barb connections are universal 1/8" NPT and can be removed and replaced with AN fittings for completely secure hose connections in race applications. Mounting provisions are universal, with two 3/8-16 tapped bolt holes in the rear for mounting to any bracket, firewall, or as desired in any position. Anodized red with the PHR logo, all fittings included.
MSRP $125.00
Your Price $99.00

Agency Power 3pc Underdrive Pulley Kit for (Z33) 350Z / G35
Part # AGP AP-Z33-130
New Page 1 Agency Power is making its way into the Nissan 350Z market. With some successful parts already in the line up, AP has developed this lightweight and under driven pulley kit to give your 350Z/G35 some more power! The CNC machined 6061 aluminum pulleys are designed to reduce rotating mass giving you quicker throttle response and increase horsepower. The pulley kit includes the crank pulley with correct timing marks, alternator pulley, and power steering pulley. Each pulley is engineered to the finest degree for a perfect fit and guaranteed performance. The 3 piece pulley kit is bead blasted for a smooth satin finish then clear anodized for a long lasting shine. Pulley kits include new belts for a proper fit. Each pulley is laser engraved with the Agency Power name. Pulley kit fits both the Nissan 350Z and Infiniti G35 manual and automatic transmissions. Made in the USA!
MSRP $325.00
Your Price $292.00

Jim Wolf Technology Camshaft Set for 2003+ 350Z
Part # JWT A3503-N00S1
S1 Cam set for VQ35DE. JWT S1 Billet cams add 16+HP while maintaining excellent driveability and idle quality. These cams are even more awesome when combined with a tuned exhaust and JWT’s Pop-charger system. 260 Degree Duration. / .428"(10.9MM) Lift, INT. Advanced 2 degrees. These cams are designed to be used with stock springs. The Pathfinder/QX4 MUST USE SPROCKET ADAPTORS. FITS: 350Z, Pathfinder, QX4, G35, Altima 2002+, Maxima 2002+, and Murano with the VQ35DE engine.
MSRP $1,198.00
Your Price $1,045.00

Power Enterprise Fan Belt for 350Z (VQ35DE)
Part # PE VB-6PK-1175
Kevlar is the same material found in bulletproof jackets and the strings attaching a parachute sail to your body. Kevlar is one of the strongest materials on earth and the best material available to construct your serpentine belt out of. Designed identical to your stock belt, this JDM piece requires no modifications. We use this belt on our 1200+rwhp 8-second Supra as well as all of our road-race cars, daily drivers, and every other application. Highly recommended!
MSRP $68.00
Your Price $62.00

Power Enterprise Mag Power II Oil Filter
Part # PE OF-0xA-2
When do you spend $18 on an oil filter? When the filter is no ordinary oil filter! Power Enterprise oil filters are the best on the market, period. Filtering to 15 microns, these filters provide exceptional filtering efficiency. 15 microns is the lowest rating at which you can filter normal motor oil. Anything smaller and even the oil can't get through the filter sufficiently. Stock oil filters average 50 microns of filtration which allows a lot more dirt and metal through than this Mag Power II. The filter paper PE uses keeps it shape better as well as it is reinforced 1.5 times. The out mesh lath supplies equal oil flow. The mesh lath core improves oil flow and helps lower pressure loss. The huge magnet (flux density of 3.000 gauss) on this filter traps small metallic dust. This neodymium magnet is excellent in heat resistance and works as stated between -20¨¬C and +140¨¬C. Also, micro-abrasive metallic contaminants can be trapped by the ¡°center mount magnet¡± system. The reinforced relief valve prevents overflow of dirty, sticky oil with sludge and metallic dust even at cold start. The silicone leak strap rubber holds oil inside to prevent any oil leakage. The bottom of the Mag Power II is seamed with a nitrile rubber gasket excellent in heat resistance. It is very important that you click on More Info and tell us exactly what car you have. Give us the make, exact model, year, and if you know the motor code give us that too just so we can double check your information. If you have swapped in a different motor than what came in your car we must have your motor code! We have these in stock for virtually every application in the world!
MSRP $24.00
Your Price $20.00
Type here your exact car model information, then click ADD TO CART

1